Easy Bookbinding


I really like this book binding method for everyone from adults to elementary age kids (though the younger kids will need a little support).  For an even easier version, requiring only paper and a stapler (or needle and thread) and scissors, check out Plum Pudding’s Paper Pocket Booklets.


Mat board scraps or other stiff board (cereal boxes aren’t sturdy enough, but you could try gluing two layers together if you can’t find anything thicker).

Paper to cover the outside (60-80 pound cardstock/scrapbook paper works well.  Typing paper is way too thin.)

Paper to cover the inside (can be thinner than the outside paper, but regular typing paper is still to thin to handle the glue.)

Paper to make your pages from (Now you can use typing paper or any other thin papers.  And remember, all of the pages don’t have to be the same type or color.)


Glue (plain white glue works well but do not use ‘school glue’)

Scrap of mat board or other stiff board to spread glue with (1/2″ – 1″ wide by 3″ long works well)

Hole punch (Make sure your hole punch can punch mat board before starting the project.  I just bought the Crop-a-dile and love it.)

Ribbon (12-18 inches per book)


Heavy books or other weight

Popsicle sticks, optional

Step 1 and 2
Step 1 and 2

Step 1: Cut 4 pieces of mat board 2 pieces that are about 1 inch long and as wide as the book and 2 pieces that are about 6 inches long and as wide as the book (4 inches wide works well).

Step 2: Cut 2 pieces of paper that are 1/2 – 3/4  inches larger in each direction than the mat board (see photo).

Step 3: Drizzle glue over the back of one large piece of mat board then use a scrap piece of mat board to evenly and very thinly coat the mat board.  (I lay the mat board on a flattened cereal box to spread the glue.  I then move the box aside to have a clean space to work with the paper.)  Position the gluey mat board on the paper, turn over and rub gently from center to edges with the flat side of the popsicle stick (or another scrap of mat board).  Place under a pile of heavy books for a few minutes while you repeat the process with the other large mat board piece.

Step 4 and 5
Step 4

Step 4: Spread glue over one of the little mat board pieces.  Line a ruler up next to the big, already glued piece to help position the little piece.  Tightly wedge 2 popsicle sticks (or 2 pieces of mat board) between the large and small pieces.  This creates a necessary gap so that the cover will hinge and open without tearing your papers.  Remove the ruler and popsicle sticks and carefully place under heavy books.  Repeat with other cover.

Step 5 and 6
Step 5 and 6

Step 5: Snip off the corners of the paper, leaving a little more than 1/8 inch of paper extending beyond the corner.  If you cut off too little it will be hard to fold the paper over the corners.  If you cut off too much, the mat board will peep through on the points.

Step 6: Fold the edges over the cover, creasing them with the popsicle stick or bone folder as you go.  Then spread a very, very thin line of glue on the edge of the mat board.  Use your popsicle stick to help press down the paper as you fold it over.  You may have to glue 2 opposite sides then let it sit under your heavy books for a minute before doing the other 2 opposite sides.

Step 7
Step 7

Step 7: Cut the end pages to go inside the cover.  They should be 1/8-1/4 inch smaller in every direction than the book cover.  Spread glue on the end pages as you did above then carefully position on the inside of the cover.  Put under a weight for a few minutes.  Before it is completely dry, run the popsicle stick in the crack between the large and small sections to make a crease.  This will help it open more easily.  Press under weights until completely dry.

Step 8: Cut the pages for the book the same size as the end pages or slightly smaller.  A stack of paper about 1/2 inch thick is good for this size book.

Step 9: Punch holes in everything.  I usually make a template that I hold over the covers and each section of papers to know where to punch the holes.  About 1/2 inch from the short end and 1 inch in seems to work well.  To make the template, get a scrap of paper the width of the book, measure carefully where you want your holes then punch them through the template.  Use this to punch holes through the cover then trim it down from both ends to match the smaller size of the pages.  Make sure everything is lining up well before you punch all of your holes.

Step 10: Use bulldog clips to hold everything together in it’s right place then tie it all up.  Thread the ribbon through the cover (make sure it is smooth on the back), the papers and front cover then tie.  I usually do a double knot and then the bow.

Finished book
Finished book





2 thoughts on “Easy Bookbinding

  1. Pingback: How To Bind A Book

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s